Aihasd 3 Pieces DRV8833 3-10V Motor Drive Module 1.5A 2 Channel Motor Drive Module Dual H Bridge DC Gear Motor Driver Controller Board Motor Drive Board Controller Board for Arduino
Aihasd 3 Pieces DRV8833 3-10V Motor Drive Module 1.5A 2 Channel Motor Drive Module Dual H Bridge DC Gear Motor Driver Controller Board Motor Drive Board Controller Board for Arduino
The Story
Aihasd 3 Pieces DRV8833 3-10V Motor Drive Module 1.5A 2 Channel Motor Drive Module Dual H Bridge DC Gear Motor Driver Controller Board Motor Drive Board Controller Board for Arduino
Technical data: 1. Driver chip: DRV8833. 2. Size: 18.5 x 16 mm. 3. Input voltage: 3V-10V. 4. Single H-bridge output current: 1.5A (it can drive two DC motors). Instructions: 1. ULT PIN: mode set. Low level is sleep mode. 2. OUT1, OUT2: 1-channel H-bridge controlled by IN1/IN2 3. OUT3, OUT4: 2-channel H-bridge controlled by IN3/IN4 4. EEP PIN: output protection. Default no connection required. 5. VCC: 3-10 V. 6. GND Product description: This is a mini dual H bridge DC motor driver breakout board, which supports over current protection, short circuit, under voltage lock and over temperature protection with low power sleep mode. With power saving mode. Purpose: each channel output 1.5A current drilling DC gear motor or 4-wire stepper motor ideal for DIY smart car robots. Note: Installing electronic modules requires basic knowledge and requires a certain electronic professional foundation and practical skills. Box contents: 3 x DRV8833 2-channel motor driver module H-bridge 4-wire stepper motor
Product Features
- This is a mini dual H bridge DC motor driver breakout board, which supports over current protection, short circuit, under voltage lock and over temperature protection with low power sleep mode. With power saving mode.
- Driver chip: DRV8833; Input voltage: 3V-10V; Size: 18.5 x 16 mm.
- The two motor outputs (A and B) can be controlled separately, the speed of each motor is controlled via a PWM input signal with a frequency up to 100 kHz.
- Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - clockwise (CW), counterclockwise (CCW), short pause and stop.
- Purpose: each channel output 1.5A current drilling DC gear motor or 4-wire stepper motor ideal for DIY smart car robots.
Details & Craftsmanship
Every detail has been carefully considered to bring you the perfect product.
Details & Craftsmanship
Every detail has been carefully considered to bring you the perfect product.
Details & Craftsmanship
Every detail has been carefully considered to bring you the perfect product.
Details & Craftsmanship
Every detail has been carefully considered to bring you the perfect product.
Details & Craftsmanship
Every detail has been carefully considered to bring you the perfect product.
Description
Aihasd 3 Pieces DRV8833 3-10V Motor Drive Module 1.5A 2 Channel Motor Drive Module Dual H Bridge DC Gear Motor Driver Controller Board Motor Drive Board Controller Board for Arduino
Technical data: 1. Driver chip: DRV8833. 2. Size: 18.5 x 16 mm. 3. Input voltage: 3V-10V. 4. Single H-bridge output current: 1.5A (it can drive two DC motors). Instructions: 1. ULT PIN: mode set. Low level is sleep mode. 2. OUT1, OUT2: 1-channel H-bridge controlled by IN1/IN2 3. OUT3, OUT4: 2-channel H-bridge controlled by IN3/IN4 4. EEP PIN: output protection. Default no connection required. 5. VCC: 3-10 V. 6. GND Product description: This is a mini dual H bridge DC motor driver breakout board, which supports over current protection, short circuit, under voltage lock and over temperature protection with low power sleep mode. With power saving mode. Purpose: each channel output 1.5A current drilling DC gear motor or 4-wire stepper motor ideal for DIY smart car robots. Note: Installing electronic modules requires basic knowledge and requires a certain electronic professional foundation and practical skills. Box contents: 3 x DRV8833 2-channel motor driver module H-bridge 4-wire stepper motor
Product Features
- This is a mini dual H bridge DC motor driver breakout board, which supports over current protection, short circuit, under voltage lock and over temperature protection with low power sleep mode. With power saving mode.
- Driver chip: DRV8833; Input voltage: 3V-10V; Size: 18.5 x 16 mm.
- The two motor outputs (A and B) can be controlled separately, the speed of each motor is controlled via a PWM input signal with a frequency up to 100 kHz.
- Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - clockwise (CW), counterclockwise (CCW), short pause and stop.
- Purpose: each channel output 1.5A current drilling DC gear motor or 4-wire stepper motor ideal for DIY smart car robots.
